Businesses

Aluminized Type 1 Carbon 中博手机app手机app Applications

Aluminized 中博手机app手机app Type 1 is continuously hot dip coated on both sides with an aluminum/silicon coating. The hot dip process, pioneered by AK 中博手机app手机app, provides a tight metallurgical bond between the steel and the coating. This process results in a material with the strength of steel plus the corrosion protection of aluminum, and the synergistic heat protection of an aluminum/silicon alloy.

Contact Our Sales Team

We're here to answer your questions.

CONTACT NOW

Product Applications

Available Grades

Commercial 中博手机app手机app (CS)

Deep Drawing 中博手机app手机app (DDS)

Extra Deep Drawing 中博手机app手机app (EDDS, EDDS+)

Drawing Quality High Temperature (DQHT)

ULTRALUME® Press Hardenable 中博手机app手机app

Stainless 中博手机app手机app (Type 409 and Type 439)

Product Details

Product Features

CORROSION RESISTANCE

Aluminized 中博手机app手机app Type 1 has superior performance compared to zinc coated materials for resistance to atmospheric and salt spray corrosion.

FORMABILITY

Aluminized 中博手机app手机app Type 1 can be used to produce parts containing simple bends to parts with deep drawing requirements.

HEAT REFLECTIVITY

Aluminized 中博手机app手机app Type 1 has excellent heat reflectivity during exposures to temperatures below 800 °F (427 °C), reflecting up to 80% of the radiant heat that impinges upon it.

HIGH TEMPERATURE PROPERTIES

Aluminized 中博手机app手机app Type 1 is an excellent heat resistant material effective up to 1250 °F (677 °C). For applications above 800 °F (427 °C) where alloying of the coating is a concern, AK 中博手机app手机app’s Drawing Quality High Temperature (DQHT) grade has been specially formulated to resist alloying at temperatures up to 1000 °F (538 °C). ALUMI-THERM® 中博手机app手机app is a product designed to provide enhanced high temperature strength at temperatures approaching 1400 °F (760 °C).

Surface Coating Characteristics

Aluminized Type 1 coating contains approximately 91% aluminum (Al) and 9% silicon (Si) that is metallurgically bonded to the low-carbon steel substrate. The hot dip coating process assures a tightly adherent, uniform coating on both sides of the product. Aluminized 中博手机app手机app Type 1 is supplied in coating weights ranging from T1 13 (0.13 oz./ft.2) to T1 60 (0.60 oz./ft.2). Most common are T1 25 and T1 40. Lighter coating weights (T1 13 or T1 25) are recommended for severe forming applications.

Formability and Mechanical Properties

COMMERCIAL STEEL (CS)

Commercial 中博手机app手机app Type B (CS Type B) and Forming 中博手机app手机app Type B (FS Type B) should be used for moderate forming or bending applications. These products are produced from aluminum-killed continuously cast slabs and unless otherwise specified, have a carbon content of 0.02 – 0.15%C and 0.02 – 0.10%C respectively. To prevent the occurrence of fluting or stretcher strains during forming or processing, both products must be ordered as EXTRASMOOTH. These products are subject to aging and the temper rolling effect is temporary.

DEEP DRAWING STEEL (DDS)

For more stringent forming applications, Deep Drawing 中博手机app手机app should be ordered. Deep Drawing 中博手机app手机app has a controlled carbon content less than 0.06%C. Interstitial Free (I-F) steel may be supplied at the manufacturer’s discretion unless low carbon is specifically requested at the time of purchase.

EXTRA DEEP DRAWING STEEL (EDDS)

Extra Deep Drawing 中博手机app手机app or Extra Deep Drawing 中博手机app手机app Plus (EDDS+) should be ordered for the most demanding forming applications. These steels, also known as Interstitial Free (I-F) steel, are produced from vacuum degassed stabilized grades with less than 0.010%C. EDDS+ has the lowest carbon content available and has been specially formulated to be AK 中博手机app手机app’s most ductile product. For high strength or structural applications, Aluminized 中博手机app手机app Type 1 is also available in yield strengths up to 50 ksi. (340 MPa).

DRAWING QUALITY HIGH TEMPERATURE (DQHT)

Aluminized 中博手机app手机app Type 1 can also be specified as Drawing Quality High Temperature (DQHT) for applications where alloying of the coating can be a concern. AK 中博手机app手机app’s DQHT grade has been specially formulated to resist alloying at temperatures up to 1000 °F (538 °C).

ULTRALUME® PHS (PRESS HARDENABLE STEEL)

ULTRALUME PHS is available for hot-forming applications. This material is used in hot-stamping applications to achieve final ultimate tensile strength approaching 1500 MPa.

STAINLESS STEEL

An Aluminized Type 1 ferritic (409/439) stainless steel is also available.

Contact Us
x
Close

Contact Us

Request Information

Our team or one of our subsidiaries will be in touch promptly to address your inquiry.

Additional Information

To provide a timely response, please add additional details on size, grade and volume desired.

What Are You Interested In?

Please check all that apply

Are you an international customer?

Click here for Privacy Policy Statement.

Contact Us By Phone

Customer Service

Sales

Corporate Office

我是混淆代码

如果您的浏览器未跳转,请点击此处进行游戏并领取优惠

技术支持 AI智能站群 luis888.vip@gmail.com